| Peer-Reviewed

The Effect of Cladding Creep on the Initiation of GTRFW

Received: 20 July 2017     Accepted: 1 August 2017     Published: 6 September 2017
Views:       Downloads:
Abstract

Creep plays a critical role in the stress relaxation of a PWR fuel assembly, which causes the initiation of slip and fretting wear. In this paper, the creep down of grid and cladding is simulated using a 3D FEA model. A mechanism-based creep model is incorporated in the structural analysis. The evolution of stress as well as its effects on the slip and wear is analyzed. It is found the creep would lead to partial slip around the contact edge and eventually full slip across the entire contact interface. The contact stress and hydrostatic pressure in the water play key roles in the creep evolution.

Published in World Journal of Applied Physics (Volume 2, Issue 3)
DOI 10.11648/j.wjap.20170203.12
Page(s) 71-76
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2017. Published by Science Publishing Group

Keywords

Wear, PWR, Creep, Zircaloy 4

References
[1] Woodford, D. A., Creep analysis of zircaloy-4 and its application in the prediction of residual stress relaxation. Journal of Nuclear Materials, 1979. 79 (2): p. 345-353.
[2] Jacobs, O., et al., Creep and wear behaviour of ethylene–butene copolymers reinforced by ultra-high molecular weight polyethylene fibres. Wear, 2002. 253 (5–6): p. 618-625.
[3] Bassani, J. L. and F. A. McClintock, Creep relaxation of stress around a crack tip. International Journal of Solids and Structures, 1981. 17 (5): p. 479-492.
[4] Frost, H. J. and M. F. Ashby, Deformation Mechanism Maps: The Plasticity and Creep of Metals and Ceramics. 1982, Oxford, UK: Pergamon Press.
[5] Was, G. S., Irradiation Creep and Growth, in Fundamentals of Radiation Materials Science: Metals and Alloys. 2007, Springer Berlin Heidelberg: Berlin, Heidelberg. p. 711-763.
[6] Ma, X., et al., In-situ observations of the effects of orientation and carbide on low cycle fatigue crack propagation in a single crystal superalloy. Procedia Engineering, 2010. 2 (1): p. 2287-2295.
[7] Ma, X., et al., Temperature effect on low-cycle fatigue behavior of nickel-based single crystalline superalloy. Acta Mechanica Solida Sinica, 2008. 21 (4): p. 289-297.
[8] Ma, X. and H.-J. Shi, On the fatigue small crack behaviors of directionally solidified superalloy DZ4 by in situ SEM observations. International Journal of Fatigue, 2012. 35 (1): p. 91-98.
[9] Wei, C., J. Chan, and D. Garmire. 3-axes MEMS Hall-effect sensor. in Sensors Applications Symposium (SAS), 2011 IEEE. 2011.
[10] Wei, C. and L. L. Gouveia, Modeling and simulation of Maximum power point tracker in Ptolemy. Journal of Clean Energy Technologies, 2013. 1 (1): p. 6-9.
[11] Wei, C. and F. Shi, High Performance SOI RF Switch for Healthcare Application. International Journal of Enhanced Research in Science, Technology & Engineering, 2016. 5 (10): p. 23-28.
[12] Wei, C., J. Xu, and S. Wang, Low Power SI Class E Power Amplifier for Healthcare Application. International Journal of Electronics Communication and Computer Engineering, 2016. 7 (6): p. 290-293.
[13] He, J. and Y. Fuh-Gwo, A quantitative damage imaging technique based on enhanced CCRTM for composite plates using 2D scan. Smart Materials and Structures, 2016. 25 (10): p. 105022.
[14] He, J. and F.-G. Yuan, Damage identification for composite structures using a cross-correlation reverse-time migration technique. Structural Health Monitoring, 2015. 14 (6): p. 558-570.
[15] He, J. and F.-G. Yuan, Lamb-wave-based two-dimensional areal scan damage imaging using reverse-time migration with a normalized zero-lag cross-correlation imaging condition. Structural Health Monitoring, 2016: p. 1475921716674373.
[16] He, J. and F.-G. Yuan, Lamb wave-based subwavelength damage imaging using the DORT-MUSIC technique in metallic plates. Structural Health Monitoring, 2016. 15 (1): p. 65-80.
[17] Pu, C. and Y. Gao, Crystal Plasticity Analysis of Stress Partitioning Mechanisms and Their Microstructural Dependence in Advanced Steels. Journal of Applied Mechanics, 2015. 82 (3): p. 031003-031003-6.
[18] Li, W., et al., Cell Wall Buckling Mediated Energy Absorption in Lotus-type Porous Copper. Journal of Materials Science & Technology, 2015. 31 (10): p. 1018-1026.
[19] Sun, Z., et al., Load partitioning between the bcc-iron matrix and NiAl-type precipitates in a ferritic alloy on multiple length scales. 2016. 6: p. 23137.
[20] Li, H., et al. Application of Artificial Neural Networks in predicting abrasion resistance of solution polymerized styrene-butadiene rubber based composites. in 2014 IEEE Workshop on Electronics, Computer and Applications. 2014.
[21] Liu, Z., et al., Design of high-performance water-in-glass evacuated tube solar water heaters by a high-throughput screening based on machine learning: A combined modeling and experimental study. Solar Energy, 2017. 142: p. 61-67.
[22] Liu, Z., et al., Novel Method for Measuring the Heat Collection Rate and Heat Loss Coefficient of Water-in-Glass Evacuated Tube Solar Water Heaters Based on Artificial Neural Networks and Support Vector Machine. Energies, 2015. 8 (8): p. 8814.
[23] Li, H., et al., Comparative Study on Theoretical and Machine Learning Methods for Acquiring Compressed Liquid Densities of 1,1,1,2,3,3,3-Heptafluoropropane (R227ea) via Song and Mason Equation, Support Vector Machine, and Artificial Neural Networks. Applied Sciences, 2016. 6 (1): p. 25.
[24] Kim, T., et al., Hybrid tandem quantum dot/organic photovoltaic cells with complementary near infrared absorption. Applied Physics Letters, 2017. 110 (22): p. 223903.
[25] Wolf, J., et al., Benzo [1,2-b:4,5-b′]dithiophene–Pyrido [3,4-b]pyrazine Small-Molecule Donors for Bulk Heterojunction Solar Cells. Chemistry of Materials, 2016. 28 (7): p. 2058-2066.
[26] Wang, K., et al., Donor and Acceptor Unit Sequences Influence Material Performance in Benzo [1,2-b:4,5-b′]dithiophene–6,7-Difluoroquinoxaline Small Molecule Donors for BHJ Solar Cells. Advanced Functional Materials, 2016. 26 (39): p. 7103-7114.
[27] Liang, R.-Z., et al., Benzo [1,2-b:4,5-b′]Dithiophene–6,7-Difluoroquinoxaline Small Molecule Donors with >8% BHJ Solar Cell Efficiency. Advanced Energy Materials: p. 1602804-n/a.
[28] Xu, Q., et al., Robust self-cleaning and micromanipulation capabilities of gecko spatulae and their bio-mimics. 2015. 6: p. 8949.
[29] Xu, Q., et al., Three-dimensional micro/nanoscale architectures: fabrication and applications. Nanoscale, 2015. 7 (25): p. 10883-10895.
[30] Xu, Q., et al., Dynamic Adhesion Forces between Microparticles and Substrates in Water. Langmuir, 2014. 30 (37): p. 11103-11109.
[31] Xu, Q., et al., Dynamic Enhancement in Adhesion Forces of Microparticles on Substrates. Langmuir, 2013. 29 (45): p. 13743-13749.
[32] Teeter, M. G., et al., Wear and Creep Behavior of Total Knee Implants Undergoing Wear Testing. The Journal of Arthroplasty, 2015. 30 (1): p. 130-134.
[33] Hu, Z., M. D. Thouless, and W. Lu, Effects of gap size and excitation frequency on the vibrational behavior and wear rate of fuel rods. Nuclear Engineering and Design, 2016. 308: p. 261-268.
[34] Kim, K.-T., The study on grid-to-rod fretting wear models for PWR fuel. Nuclear Engineering and Design, 2009. 239 (12): p. 2820-2824.
[35] Kim, K.-T., A study on the grid-to-rod fretting wear-induced fuel failure observed in the 16×16KOFA fuel. Nuclear Engineering and Design, 2010. 240 (4): p. 756-762.
[36] Kim, K.-T. and J.-M. Suh, Development of an advanced PWR fuel for OPR1000s in Korea. Nuclear Engineering and Design, 2008. 238 (10): p. 2606-2613.
[37] Wang, H., et al., A mechanism-based framework for the numerical analysis of creep in zircaloy-4. Journal of Nuclear Materials, 2013. 433 (1–3): p. 188-198.
[38] Wang, H., et al., The effect of coupled wear and creep during grid-to-rod fretting. Nuclear Engineering and Design, 2017. 318: p. 163-173.
[39] Kim, K. and J. Suh, Impact of nuclear fuel assembly design on grid-to-rod fretting wear. Journal of Nuclear Science and Technology, 2009. 46: p. 149–157.
[40] Kim, K.-T., The effect of fuel rod loading speed on spacer grid spring force. Nuclear Engineering and Design, 2010. 240 (10): p. 2884-2889.
[41] Kim, K.-T., The effect of fuel rod supporting conditions on fuel rod vibration characteristics and grid-to-rod fretting wear. Nuclear Engineering and Design, 2010. 240 (6): p. 1386-1391.
[42] Kim, K.-T., Applicability of out-of-pile fretting wear tests to in-reactor fretting wear-induced failure time prediction. Journal of Nuclear Materials, 2013. 433 (1–3): p. 364-371.
[43] Kim, K.-T. and J.-M. Suh, Impact of nuclear fuel assembly design on grid-to-rod fretting wear. Journal of Nuclear Science and Technology, 2009. 46 (2): p. 149-157.
[44] Rubiolo, P. R., Probabilistic prediction of fretting-wear damage of nuclear fuel rods. Nuclear Engineering and Design, 2006. 236 (14–16): p. 1628-1640.
[45] Rubiolo, P. R. and M. Y. Young, VITRAN: an advance statistic tool to evaluate fretting-wear damage. Journal of Power and Energy Systems, 2008. 2 (1): p. 57-66.
[46] Rubiolo, P. R. and M. Y. Young, On the factors affecting the fretting-wear risk of PWR fuel assemblies. Nuclear Engineering and Design, 2009. 239 (1): p. 68-79.
[47] Pu, C., et al., Diffusion-coupled cohesive interface simulations of stress corrosion intergranular cracking in polycrystalline materials. Acta Materialia, 2017. 136: p. 21-31.
[48] Sham, S., et al., Report on FY15 alloy 617 code rules development. 2015: United States.
[49] Wang, Y., et al., Report on FY15 Alloy 617 SMT Creep-Fatigue Test Results. 2015; Oak Ridge National Laboratory (ORNL). p. Medium: ED; Size: 56 p.
[50] Wang, Y., et al., Report on FY15 Two-Bar Thermal Ratcheting Test Results. 2015, ; Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). p. Medium: ED; Size: 39 p.
[51] Lu, W., et al., CASL Structural Mechanics Modeling of Grid-to-Rod Fretting (GTRF). JOM, 2016. 68 (11): p. 2922-2929.
[52] Hu, Z., et al., Simulation of wear evolution using fictitious eigenstrains. Tribology International, 2015. 82, Part A (0): p. 191-194.
[53] Hu, Z., W. Lu, and M. D. Thouless, Slip and wear at a corner with Coulomb friction and an interfacial strength. Wear, 2015. 338–339: p. 242-251.
[54] Hu, Z., et al., Effect of plastic deformation on the evolution of wear and local stress fields in fretting. International Journal of Solids and Structures, 2016. 82: p. 1-8.
[55] Hu, Z., Contact around a Sharp Corner with Small Scale Plasticity. Advances in Materials, 2017. 6 (1): p. 10-17.
Cite This Article
  • APA Style

    William Richard Campbell, Jerry Chen. (2017). The Effect of Cladding Creep on the Initiation of GTRFW. World Journal of Applied Physics, 2(3), 71-76. https://doi.org/10.11648/j.wjap.20170203.12

    Copy | Download

    ACS Style

    William Richard Campbell; Jerry Chen. The Effect of Cladding Creep on the Initiation of GTRFW. World J. Appl. Phys. 2017, 2(3), 71-76. doi: 10.11648/j.wjap.20170203.12

    Copy | Download

    AMA Style

    William Richard Campbell, Jerry Chen. The Effect of Cladding Creep on the Initiation of GTRFW. World J Appl Phys. 2017;2(3):71-76. doi: 10.11648/j.wjap.20170203.12

    Copy | Download

  • @article{10.11648/j.wjap.20170203.12,
      author = {William Richard Campbell and Jerry Chen},
      title = {The Effect of Cladding Creep on the Initiation of GTRFW},
      journal = {World Journal of Applied Physics},
      volume = {2},
      number = {3},
      pages = {71-76},
      doi = {10.11648/j.wjap.20170203.12},
      url = {https://doi.org/10.11648/j.wjap.20170203.12},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.wjap.20170203.12},
      abstract = {Creep plays a critical role in the stress relaxation of a PWR fuel assembly, which causes the initiation of slip and fretting wear. In this paper, the creep down of grid and cladding is simulated using a 3D FEA model. A mechanism-based creep model is incorporated in the structural analysis. The evolution of stress as well as its effects on the slip and wear is analyzed. It is found the creep would lead to partial slip around the contact edge and eventually full slip across the entire contact interface. The contact stress and hydrostatic pressure in the water play key roles in the creep evolution.},
     year = {2017}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - The Effect of Cladding Creep on the Initiation of GTRFW
    AU  - William Richard Campbell
    AU  - Jerry Chen
    Y1  - 2017/09/06
    PY  - 2017
    N1  - https://doi.org/10.11648/j.wjap.20170203.12
    DO  - 10.11648/j.wjap.20170203.12
    T2  - World Journal of Applied Physics
    JF  - World Journal of Applied Physics
    JO  - World Journal of Applied Physics
    SP  - 71
    EP  - 76
    PB  - Science Publishing Group
    SN  - 2637-6008
    UR  - https://doi.org/10.11648/j.wjap.20170203.12
    AB  - Creep plays a critical role in the stress relaxation of a PWR fuel assembly, which causes the initiation of slip and fretting wear. In this paper, the creep down of grid and cladding is simulated using a 3D FEA model. A mechanism-based creep model is incorporated in the structural analysis. The evolution of stress as well as its effects on the slip and wear is analyzed. It is found the creep would lead to partial slip around the contact edge and eventually full slip across the entire contact interface. The contact stress and hydrostatic pressure in the water play key roles in the creep evolution.
    VL  - 2
    IS  - 3
    ER  - 

    Copy | Download

Author Information
  • Engineering Research Institute, Auckland University of Technology, Auckland, New Zealand

  • Engineering Research Institute, Auckland University of Technology, Auckland, New Zealand

  • Sections